Study into the effect of plasticizer nature on the properties of polymer-bitumen compositions via fluorescence microscopy

The paper studies how the nature of the plasticizer affects the properties of polymer-bitumen compositions using the fluorescence microscopy. The current petroleum road bitumen used for the construction of road, bridge, and airfield pavements does not meet the requirements for cracking/heat resistance, elasticity, and adhesion to the mineral material surface. Pavement performance characteristics can be significantly improved by introducing thermoplastic elastomers, plasticizers, and surfactants into the composition of petroleum road bitumen. The best results were obtained when using a block copolymer of styrene and butadiene, industrial oil, and cationic surfactant on the basis of polyaminoamides and polyaminoimidazolines. The choice of industrial oil as a plasticizer is attributed to its good compatibility with bitumen and polymer, as well as its high flash point (200 °С). The content of paraffin-naphthenic hydrocarbons in industrial oil is over 70%. Although industrial oil is produced in large quantities, an acute shortage of this petrochemical product is observed due to its wide application; thus, intensive studies are underway to replace industrial oil in the composition of the polymer-bitumen binder. It is proposed to use heavy gas oil produced via catalytic cracking and delayed coking, heavy pyrolysis tar, solvent-extracted oil, and tall oil as plasticizers in the creation of the polymer-bitumen binder. In this connection, the effect of proposed plasticizers on the colloidal structure of the polymer-bitumen binder was studied using the method of fluorescence microscopy. Initial polymer-bitumen binders were produced at ANHK (Angarsk) according to GOST R 52056-2003 Polymer-Bitumen Road Binders Based on Styrene-Butadiene-Styrene-Type Block Polymers. The group composition of the plasticizers under study was determined. It was shown that in order to obtain a polymer-bitumen binder resistant to stratification, plasticizers having a content of aromatic compounds of over 60% are required.

1. Gokhman L. M. Polymer-bitumen binders based on SBS for road construction. Moscow: Informavtodor; 2002. 110 p. (In Russian).

2. Airey G. D. Fundamental binder and practical mixture evaluation of polymer modified bituminous materials. International Journal of Pavement Engineering. 2004;5(3):137-151. https://doi.10.1080/10298430412331314146.

3. Polacco G. A review of the fundamentals of polymer-modified asphalts: asphalt/polymer interactions and principles of compatibility advances in colloid and interface science. Advances in Colloid and Interface Science. 2015;224:72-112. https://doi.10.1016/j.cis.2015.07.010.

4. Gogoi R., Biligiri K. P., Das N. C. Performance prediction analyses of styrenebutadiene rubber and crumb rubber materials in asphalt road applications. Materials and Structures. 2016;49(9):3479-3493. https://doi.10.1617/s11527-015-0733-0.

5. Karger-Kocsis J., Meszaros L., Barany T. Ground tyre rubber (GTR) in thermoplastics, thermosets, and rubbers. Journal of Materials Science. 2013;48(1):1-38. https://doi.10.1007/s10853-012-6564-2.

6. Alonso S., Medina-Torres L., Zitzumbo R., Avalos F. Rheology of asphalt and styrene-butadiene blends. Journal of Materials Science. 2010;45(10):2591-2597. https://doi.10.1007/s10853-010-4230-0.

7. Diab A. Studying viscosity of asphalt binders and effect of varied production temperatures on engineering properties of hot mix asphalt mixtures. Canadian Journal of Civil Engineering. 2016;44(1):1-9. https://doi.org/10.1139/cjce-2016-0383.

8. Zhang F., Yu J., Wu S. Effect of ageing on rheological properties of storage-stable SBS/sulfurmodified asphalts. Journal of Hazardous Materials. 2010;182(1-3):507-517. https://doi.10.1016/j.jhazmat.2010.06.061.

9. Airey G. D. Rheological properties of styrene butadiene styrene polymer modified road bitumens. Fuel. 2003;82(14):1709-1719. https://doi.10.1016/S0016-2361(03)00146-7.

10. Gokhman L. M., Gavrilenko O. V. Influence of binding agent elasticity on fatigue resistance of polymer-asphalt concrete. Nauka i tekhnika v dorozhnoi otrasli = Science and Engineering for Highways. 2011;59(4):21-25. (In Russian).

11. Tyukilina P. M., Gureev A. A. Regularities of influence of plasticizer composition on elasticity and cohesion strength of polymer-bitumen binders. Neftepererabotka i neftekhimiya. Nauchno-tekhnicheskie dostizheniya i peredovoi opyt. 2018;(2):12-16. (In Russian).

12. Gokhman L. M. Polymer selection and PMB preparation. Avtomobil’nye dorogi. 2016;(2):55-61.

13. Petrov K. R., Daurov Z. S., Tikhonov R. S. Problems and methods of road coverings construction on weak bases. Forum molodykh uchenykh. 2017;16(12):1448-1452. (In Russian).

14. Belyaev P. S., Polushkin D. L., Makeev P. V., Frolov V. A. Petroleum bitumen modified by polymer materials for asphalt concrete surfacing with improved operational performance. Vestnik Tambovskogo gosudarstvennogo tekhnicheskogo universiteta = Transaction of the Tambov State Technical University. 2016;22(2):264-271. (In Russian). https://doi.10.17277/vestnik.2016.02.pp.264-271.

15. Plewa A., Belyaev P. S., Andrianov K. A., Zubkov A. F., Frolov V. A. The effect of modifying additives on the consistency and properties of bitumen binders. Advanced Materials & Technologies. 2016;(4):35-40. https://doi.10.17277/amt.2016.04.pp.035-040.

16. Polacco G., Stastna J., Biondi D., Antonelli F., Vlachovicova Z., Zanzotto L. Rheologe of asphalts modified with glycidylmethacrylata functionalized polymers. Journal of Colloid and Interface Science. 2004;280(2):366-373. https://doi.10.1016/j.jcis.2004.08.043.

17. Abdullah M. E., Zamhari K. A., Shamshudin M. K., Mohd Rosli H., Idham M. K. Rheological properties of asphalt binder modified with chemical warm asphalt additive. Advanced Materials Research. 2013;671:1692-1699. https://doi.10.4028/www.scientific.net/amr.671-674.1692.

18. Evdokimova N. G., Egorova N. A., Sultanova D. P., Kunakkulova E. M., Serezhkina N. G. The formation of the sol-gel nanostructures of road bitumen by selecting chemical group composition. Nanotekhnologii v stroitel’stve = Nanotechnologies in Construction. 2019;11(5):512-525. (In Russian). https://doi.10.15828/2075-8545-2019-11-5-512-525.

19. Vysotskaya M. A., Kuznecov D. A., Litovchenko D. P., Barkovskiy D. V., Shiryaev A. O. The need for a plasticizer in the production of polymeric-bitumen binders. Vestnik Belgorodskogo gosudarstvennogo tekhnologicheskogo universiteta im. V. G. Shukhova = Bulletin of Belgorod State Technological University Named After V. G. Shukhov. 2019;(5):16-22. (In Russian). https://doi.10.34031/article_5cd6df466b-b9e0.32764094.